Flush Mount Camera with Programmer For 2017-2020 Super Duty Cab and Chassis
Includes programmer
FMVSS 111 compliant! This kit is for Cab and Chassis vehicles only and these are rare so chances are you need the non-Cab and Chassis version. See the compatibility tab for details before purchasing this kit. This is a plug and play camera kit that will allow you to add a camera to a cab and chassis truck that has been pre-wired at the factory and has a 4.2" or 8" factory display. Your truck must be prewired for a camera or this kit will not work. Please see the compatibility tab for more information!
Use this camera for factory ordered cab and chassis trucks. This universal camera mounts flush with a flat surface. Drill a 22.5mm hole(hole saw included) and run the cable through to your factory backup camera connection.
The kit also comes with the radio programmer tool so you can turn on the camera function quickly and easily- without having to go to a dealer!
Kit includes the following:
- Black rear facing surface mount camera with our latest super CMOS camera - the latest camera technology!
- OBD Programmer
- OEM conversion harness 6',9',16',32',64' cable lengths available. Select from drop down above.
- 22.5 mm hole saw
- Installation instructions
- 3 year limited camera warranty
Camera Specifications:
- Super CMOS chip - outstanding color, contrast, and clarity!
- Removable parking guidelines
- 150 degree view
- 600 TV lines of resolution
- .1 lux minimum illumination - Outstanding night vision!
**Not compatible with Super Duty trucks that have the 360 degree view system** See CS-FTRSKLP-17SD-TRL.
SKU | CS-17SDFM4-CCP |
---|---|
Video System | NTSC |
Waterproof/Dustproof Level | IP 67 |
Night Vision | < .2 Lux |
Power Supply | 12 Volts |
System Manufacturer | EVI Systems |
Camera Resolution | 600 TVL |
Parking Guidelines | Selectable on/off |
Camera Orientation | Rear Facing |
Fit Type | Universal fit |
Connection | Factory Connector |
Sensor Type | Super CMOS |
Viewing Angle | 150 Degrees |
Warranty | 3 Year |
Camera Type | Rear Camera, Utility Bed Camera Systems |
Vehicle Category | Truck, Fleet Vehicle (i.e. cargo van) |
Number of Cameras | 1 |
Reason for Shopping | Adding the camera(s) |
Wiring Type | Factory Plug&Play |
Camera Mount Location | Camper/Utility Bed, Universal Mount |
For a monitor it uses | Your factory display |
Radio Screen Size | 4.2” Ford, 8” Ford Sync 2, 8" Ford Sync 3 |
Make | Ford |
Model | Cab & Chassis |
Year | 2017,2018,2019,2020 |
Make Filter | Ford |
Model Filter | Cab & Chassis |
Year Filter | 2017, 2018, 2019, 2020 |
2017-2020 Ford® Super Duty F350, F450, F550 cab and chassis trucks that have been pre-wired for a camera from the factory and have a 4.2" or 8" SYNC 3 display from the factory.
This kit relies on the factory camera chassis harness to operate.
Not compatible if your truck has the 360 view system.
See our other Super Duty truck options if your truck came from the factory with a bed and you are removing the bed to add service body, utility bed, dump truck, flat bed, and any other application where you do not have a tailgate. This kit will only work on the trucks that came from the factory without a bed. Please verify the connector shown in the photos against the connector on your truck before ordering. If you are still not sure please call us for assistance.
**EVI Systems has certified this camera system to comply with FMVSS 111 regulations as set forth by the National Highway Traffic Safety Administration (NHTSA). Testing has been performed jointly in-house and by a certified laboratory to meet or exceed the minimum requirements set forth by TP-111-V-01. FMVSS 111 field of view requirements and any other vehicle related certification is ultimately the responsibility of the vehicle up-fitter to ensure compliance.
Camera requires a 22.5 mm hole on a flat surface for flush mounting. It will require a flat section approximately 1" x 1" for mounting. Drill the hole and connect the camera harness to the OEM conversion harness. Run the cable to your factory backup camera connection under the truck and plug it in.
Q: Can the OBD programmer be used on more than one vehicle?
A: No, the programmer is VIN locked to your vehicle after one use. Once the seal on the programmer is broken the programmer can't be returned. After you've programmed your factory radio it is recommended that you store the programmer in the glovebox just in case programming is ever lost due to vehicle servicing, etc.
NOTE: Your question may be included on the product page but your name will not be displayed for privacy reasons.
10% OFF Discount for Military and Public Service Workers
Thank You Veterans and Civil Servants!
Get the Discount10% OFF Discount for Military and Public Service Workers
Thank You Veterans and Civil Servants!
Get the Discount