Backup Camera for 8" SYNC 3 Display, Fits 2017+ Super Duty
Availabilty: In stock
SKU
CS-17FTRSD-OBDS3
$546.00
Factory OEM handle with Camera!
This is an OEM backup camera solution for your Ford® Super Duty truck with 8" SYNC 3 factory display! This will fit the new generation 2017+ Super Duty pickup trucks as a direct factory replacement handle with pre-mounted CMOS camera. See the bumper and hitch while hooking up trailers! This kit will look like it was installed at the factory, but cost you a fraction of the price!
Kit includes:
- Super CMOS camera mounted in an OEM Ford® rear handle system. Black handle
- 25' wiring harness-Loomed for extra protection!
- OBD programmer for radio
- T-harness to create the camera connection to your factory radio
- Wire connectors
- Zip ties
- Detailed installation instructions
Camera Specifications:
- Sensor: SUPER CMOS
- Resolution: 600 TV lines
- Minimum Illumination: <0.2 Lux
- View Angle: 170
- Working Voltage: DC 9-16V
- Video Color: Full
- Parking Line: On/Off switchable
- Operating Temperature: -30C to +70C
- Water proof: IP67
This kit allows you to see what is directly behind the truck, including the bumper and hitch, and will look like it came from the factory! Camera is secured into the OEM handle using screws, not glue like others out there.
Display is not included as this kit connects to your existing factory display.
This camera comes with a 3 year warranty and is guaranteed to fit or your money back. Professional installation is recommended.
SKU | CS-17FTRSD-OBDS3 |
---|---|
Video System | NTSC |
Waterproof/Dustproof Level | IP 67 |
Night Vision | .2 Lux |
Power Supply | 12 Volts |
System Manufacturer | EVI Systems |
Camera Resolution | 600 TVL |
Parking Guidelines | Selectable on/off |
Camera Orientation | Rear Facing |
Connection | RCA with opt. Factory Interface |
Sensor Type | Super CMOS |
Viewing Angle | 170 Degrees |
Warranty | 3 Year |
Camera Type | Rear Camera |
Vehicle Category | Truck |
Number of Cameras | 1 |
Reason for Shopping | Adding the camera(s) |
Wiring Type | Hard Wired |
Camera Mount Location | Factory Tailgate |
For a monitor it uses | Your factory display |
Radio Screen Size | 8" Ford Sync 3 |
Make | Ford |
Model | Super Duty |
Year | 2017,2018,2019 |
Make Filter | Ford |
Model Filter | Super Duty |
Year Filter | 2017, 2018, 2019 |
Compatible with 2017+ F250, F350, F450, and F550 with an 8" SYNC 3 display.
The rear camera kit will replace your factory rear tailgate handle. Route the power/video RCA into the cab. Open the dash to access the back of your factory SYNC 3 display and connect the included T- harness to the display. Connect camera power wire to a 12v reverse power source. Connect black ground wire to a suitable ground on the frame.
Make installation even easier with an add on 12 Volt power source to eliminate the need to locate a power source on the vehicle and avoid cutting or splicing into factory wiring! See related item SKU: CS-RPW-P
Plug the OBD programmer into your truck's OBD port under the steering column to program the radio. Takes 1-2 minutes to program!
Write Your Own Review
Q: Can the OBD programmer be used on more than one vehicle?
A: No, the programmer is VIN locked to your vehicle after one use. Once the seal on the programmer is broken the programmer can't be returned. After you've programmed your factory radio it is recommended that you store the programmer in the glovebox just in case programming is ever lost due to vehicle servicing, etc.
NOTE: Your question may be included on the product page but your name will not be displayed for privacy reasons.
10% OFF Discount for Military and Public Service Workers
Thank You Veterans and Civil Servants!
Get the Discount10% OFF Discount for Military and Public Service Workers
Thank You Veterans and Civil Servants!
Get the Discount Do You Need Any Help? Give Us a Call. 888-844-9763